Maxon WL7 Betriebsanleitung

1 PATENTS PENDINGMP-06-10REV. A APRIL 2009WHEELCHAIR LIFT MODEL NO. • WL7-vers. C • WL7-vers. C-1KOPERATING INSTRUCTIONSFOR© M

PATENTS PENDING 10LIFT COMPONENTS & TERMINOLOGYINBOARDLEFTOUTBOARD512312LIFT COMPONENTS (SEE TABLE 11-1)FIG. 10-16410267

11 PATENTS PENDINGTABLE 11-1ITEM NAME DESCRIPTION1. THRESHOLD PLATE Component that bridges the entry way, through the Lift,

PATENTS PENDING 12All WARNING, CAUTION, and OPERATION decals provided with Wheelchair Lift must always be in place on the Li

13 PATENTS PENDINGDECAL SET P/N 268302-01FIG. 13-1DECALS FOR WL7-vers. C

PATENTS PENDING 14DECAL SET P/N 268302-03FIG. 14-1DECALS FOR WL7-vers. C-1K DECALS AND DECAL PLACEMENT- Continued

15 PATENTS PENDINGSERIAL PLATEP/N 905246-8FIG. 15-1CONTROLLER OVERLAYP/N 2667630-01FIG. 15-2SERIAL PLATE & CONTROLLER OVER

PATENTS PENDING 16ANTI-SLIP TAPEP/N 096020-10ANTI-SLIP TAPE(ROLLSTOP)P/N 096020-13YELLOW TAPE(BOTTOM-ROLLSTOP)P/N 905293-17(

17 PATENTS PENDING(33” WIDE PLATFORM)YELLOW TAPE(BOTTOM-ROLLSTOP)P/N 905293-18ANTI-SLIP TAPEP/N 096020-11ANTI-SLIP TAPE(ROLLST

PATENTS PENDING 18(34” WIDE PLATFORM)YELLOW TAPE(BOTTOM-ROLLSTOP)P/N 905293-18ANTI-SLIP TAPEP/N 096020-12ANTI-SLIP TAPE(ROLL

19 PATENTS PENDINGTHIS PAGE INTENTIONALLY LEFT BLANK

PATENTS PENDING

PATENTS PENDING 20ENTER VEHICLE1. Fully open and secure Wheel-chair Lift access door(s) on the vehicle.UNFOLD PLATFORMFIG. 2

21 PATENTS PENDINGPOSITIONING OCCUPANT ON PLATFORM AT GROUND LEVELFIG. 21-45. If equipped, unfasten seat belt (FIG. 21-2). Pla

PATENTS PENDING 228. Push the UP switch on hand pendant (FIG. 22-2) to raise platform to vehicle fl oor level (FIG. 22-3).HAN

23 PATENTS PENDING1. Fully open and secure Wheel-chair Lift access door(s) on the vehicle.2. Push the UNFOLD switch on hand pe

PATENTS PENDING 246. If equipped, unfasten seat belt (FIG. 24-1). Place on hanger (FIG. 24-2).7. Release wheelchair brakes o

25 PATENTS PENDINGSTOW LIFTFOLDING PLATFORM UP INTO VEHICLEFIG. 25-4HAND PENDANTFIG. 25-21. If equipped, fasten seat belt (FIG

PATENTS PENDING 26MANUAL PUMP OPERATIONLOADING & UNLOADING OCCUPANT1. Reposition latches to manually unfold the Lift as

27 PATENTS PENDING3. Unfold the platform as fol-lows. Open release valve on manual pump by turning manual backup handle coun-t

PATENTS PENDING 286. Ensure outboard rollstop is raised all the way (FIG. 28-1).OUTBOARD ROLLSTOPRAISED UPFIG. 28-1 7. If eq

29 PATENTS PENDING10. Watch platform (FIG. 29- 3) as it lowers occupant to the ground.LOWERING PLATFORMTO GROUNDFIG

TABLE OF CONTENTSINTRODUCTION ... 4SAFETY SUMMARY ...

PATENTS PENDING 3013. Ensure outboard rollstop on the platform is opened to the horizontal position (FIG.

31 PATENTS PENDINGHANDLE FULLY ENGAGEDFIG. 31-2HANDLE - NOTCHESLINED UP CORRECTLY FIG. 31-1NOTCHES LINED UP VE

PATENTS PENDING 3219. Stow the Lift as follows. Pump the manual backup handle up and down (FIG. 32-1) unti

PATENTS PENDING 4INTRODUCTIONSAFETY SUMMARY1. This Wheelchair Lift is intended for commercial use only and should be operate

5 PATENTS PENDING6. If possible, park the vehicle on level ground. Always set the vehicle emergency brake before operating the

PATENTS PENDING 6If the Lift is dirty, clean it.DAILY PRE-OPERATION & OPERATION CHECKLISTNOTE: PRE-OPERATION and OPERATI

7 PATENTS PENDINGUse Lift operating instructions in this manual to UNFOLD, LOWER, RAISE, and FOLD platform. Make sure the Lift

PATENTS PENDING 8MAINTENANCE SCHEDULENOTE: Only a qualifi ed technician should do the scheduled main- tenance on t

9 PATENTS PENDINGTHIS PAGE INTENTIONALLY LEFT BLANK